For A2L
| What's in the kit? | What is it and when to replace? | How to replace? |
| Silicone Sock for Hotend - 3 pcs | The silicone sock is a black cover that serves the primary function of maintaining nozzle temperature stability and isolating impurities, preventing the filament from soiling the nozzle and affecting print quality. You should replace the silicone hotend cover if any of the following signs occur: 1. Cracks or Damage 2. Looseness or Detachment: 3. Deformation Due to Prolonged High Temperatures: 4. Frequent Filament Build-up on the Heating Block 5. Discoloration or Brittleness 6. Friction With Moving Parts (e.g, Nozzle Wiper) |
Bambu Lab Wiki |
| Heatbed Nozzle Wiper - 3 pcs |
Over time, the silicone wiper bristles can become damaged, and the metallic wiper may wear out or become bent. Common issues that may indicate the need for replacement:
1. Inadequate cleaning of the nozzle during the pre-print preparation step. 2. Filament adhering to the nozzle tip during bed leveling, resulting in an inconsistent first layer. 3. Visible damage or wear on the nozzle wiper. |
Bambu Lab Wiki |
|
Replacement Filament Cutter - 3 pcs |
The Filament Cutter is a blade that is used to cut the filament during a filament change. The sharpness of the blade can become worse over time. We recommend replacing the filament cutter every 10-15 spools of filament used (or quicker) to ensure the cutting performance is unaffected. | |
| PTFE Tube (4000mm) - 1 pc | The function of PTFE Tube is to reduce resistance and guide filament. If the tubes are worn and not replaced in time, this may lead to feeding failures, filament accumulation inside the AMS, etc. We recommend that you check the PTFE tubes for wear during your maintenance of the machine. | |
| Lubricant Grease - 6g | Lubricant Grease is used to lubricate lead screws, or to eliminate noise issues between belts and idle pulleys. Inspect and reapply lubricant to lead screws and guide rails approximately every 3 months. | |
| Lubricant Oil (3g) - 6 pcs | Lubricant Oil is typically used for the lubrication of linear guides, slide rails, and steel shafts. Inspect and reapply lubricant to lead screws and guide rails approximately every 3 months. | |
| Nozzle Cleaning Sponge - 3 pcs | During daily printing, nozzles easily accumulate filament residue. Over time, this residue can carbonize and turn black, affecting print accuracy. This cleaning sponge is made of high-temperature resistant material and is specially designed to clean stubborn dirt from the hot-end nozzles of printers. It effectively removes carbonized residue, ensuring optimal print quality. It is compatible with nozzles on all printer models. |
For X2D
| What's in the kit? | What is it and when to replace? | How to replace? |
| Silicone Sock for Hotend - 3 pcs | The silicone sock is a black cover that serves the primary function of maintaining nozzle temperature stability and isolating impurities, preventing the filament from soiling the nozzle and affecting print quality. You should replace the silicone hotend cover if any of the following signs occur: 1. Cracks or Damage 2. Looseness or Detachment: 3. Deformation Due to Prolonged High Temperatures: 4. Frequent Filament Build-up on the Heating Block 5. Discoloration or Brittleness 6. Friction With Moving Parts (e.g, Nozzle Wiper) |
Bambu Lab Wiki |
| Nozzle Wiping Pad - 3 pcs |
The Nozzle Wiping Pad is installed on the nozzle wiper part of the purge wiper and is used to remove residual waste on the nozzle. It is made of soft silicone material to ensure good contact with the hotend during wiping. Replace the nozzle wiping pad if it is damaged or detached.
|
Bambu Lab Wiki |
| Air Filter - 1 pc | The Air Filter is installed on the inner side of the right inner liner of the printer (closer to the printer chamber) and is used to filter the air inside the chamber, effectively removing VOCs. It is advisable to replace the air filter after a total printing time of 1440 hours (or 60 days). | |
| The Filament Cutter is a blade that is used to cut the filament during a filament change. The sharpness of the blade can become worse over time. We recommend replacing the filament cutter every 10-15 spools of filament used (or quicker) to ensure the cutting performance is unaffected. | ||
| PTFE Tube (4000mm) - 1 pc | The function of PTFE Tube is to reduce resistance and guide filament. If the tubes are worn and not replaced in time, this may lead to feeding failures, filament accumulation inside the AMS, etc. We recommend that you check the PTFE tubes for wear during your maintenance of the machine. | |
| Lubricant Grease - 6g | Lubricant Grease is used to lubricate lead screws, or to eliminate noise issues between belts and idle pulleys. Inspect and reapply lubricant to lead screws and guide rails approximately every 3 months. | |
| Lubricant Oil (3g) - 6 pcs | Lubricant Oil is typically used for the lubrication of linear guides, slide rails, and steel shafts. Inspect and reapply lubricant to lead screws and guide rails approximately every 3 months. | |
| Nozzle Cleaning Sponge - 3 pcs | During daily printing, nozzles easily accumulate filament residue. Over time, this residue can carbonize and turn black, affecting print accuracy. This cleaning sponge is made of high-temperature resistant material and is specially designed to clean stubborn dirt from the hot-end nozzles of printers. It effectively removes carbonized residue, ensuring optimal print quality. It is compatible with nozzles on all printer models. | |
| Molecular Sieve Desiccant - 6 pcs | The molecular sieve desiccant absorbs moisture and keeps the air inside the AMS unit dry, working perfectly alongside the active heater. After the desiccant absorbs sufficient moisture, the indicating particles inside will turn from yellow to purple. When the color changes fully, it needs to be replaced with a new desiccant. | / |
| Silicone Desiccant - 6 pcs | The color-changing silicone desiccant absorbs moisture and keeps the air inside AMS unit dry. After the desiccant absorbs sufficient moisture, the yellow particles inside will turn purple. When the desiccant turns purple, it needs to be replaced with a new desiccant. | / |
For P2S
| What's in the kit? | What is it and when to replace? | How to replace? |
| Silicone Sock for Hotend - 3 pcs | The silicone sock is a black cover that serves the primary function of maintaining nozzle temperature stability and isolating impurities, preventing the filament from soiling the nozzle and affecting print quality. You should replace the silicone hotend cover if any of the following signs occur: 1. Cracks or Damage 2. Looseness or Detachment: 3. Deformation Due to Prolonged High Temperatures: 4. Frequent Filament Build-up on the Heating Block 5. Discoloration or Brittleness 6. Friction With Moving Parts (e.g, Nozzle Wiper) |
Bambu Lab Wiki |
| Nozzle Wiping Pad - 3 pcs |
The Nozzle Wiping Pad is installed on the nozzle wiper part of the purge wiper and is used to remove residual waste on the nozzle. It is made of soft silicone material to ensure good contact with the hotend during wiping. Replace the nozzle wiping pad if it is damaged or detached.
|
Bambu Lab Wiki |
| Air Filter - 1 pc | The Air Filter is installed on the inner side of the right inner liner of the printer (closer to the printer chamber) and is used to filter the air inside the chamber, effectively removing VOCs. It is advisable to replace the air filter after a total printing time of 1440 hours (or 60 days). | |
|
Replacement Filament Cutter - 3 pcs |
The Filament Cutter is a blade that is used to cut the filament during a filament change. The sharpness of the blade can become worse over time. We recommend replacing the filament cutter every 10-15 spools of filament used (or quicker) to ensure the cutting performance is unaffected. | |
| PTFE Tube (4000mm) - 1 pc | The function of PTFE Tube is to reduce resistance and guide filament. If the tubes are worn and not replaced in time, this may lead to feeding failures, filament accumulation inside the AMS, etc. We recommend that you check the PTFE tubes for wear during your maintenance of the machine. | |
| Lubricant Grease - 6g | Lubricant Grease is used to lubricate lead screws, or to eliminate noise issues between belts and idle pulleys. Inspect and reapply lubricant to lead screws and guide rails approximately every 3 months. | |
| Lubricant Oil (3g) - 6 pcs | Lubricant Oil is typically used for the lubrication of linear guides, slide rails, and steel shafts. Inspect and reapply lubricant to lead screws and guide rails approximately every 3 months. | |
| Nozzle Cleaning Sponge - 3 pcs | During daily printing, nozzles easily accumulate filament residue. Over time, this residue can carbonize and turn black, affecting print accuracy. This cleaning sponge is made of high-temperature resistant material and is specially designed to clean stubborn dirt from the hot-end nozzles of printers. It effectively removes carbonized residue, ensuring optimal print quality. It is compatible with nozzles on all printer models. | |
| Molecular Sieve Desiccant - 6 pcs | The molecular sieve desiccant absorbs moisture and keeps the air inside the AMS unit dry, working perfectly alongside the active heater. After the desiccant absorbs sufficient moisture, the indicating particles inside will turn from yellow to purple. When the color changes fully, it needs to be replaced with a new desiccant. | / |
| Silicone Desiccant - 6 pcs | The color-changing silicone desiccant absorbs moisture and keeps the air inside AMS unit dry. After the desiccant absorbs sufficient moisture, the yellow particles inside will turn purple. When the desiccant turns purple, it needs to be replaced with a new desiccant. | / |
For H2D
| What's in the kit? | What is it and when to replace? | How to replace? |
| Silicone Sock for Hotend - 3 pcs | The silicone sock is a black cover that serves the primary function of maintaining nozzle temperature stability and isolating impurities, preventing the filament from soiling the nozzle and affecting print quality. You should replace the silicone hotend cover if any of the following signs occur: 1. Cracks or Damage 2. Looseness or Detachment: 3. Deformation Due to Prolonged High Temperatures: 4. Frequent Filament Build-up on the Heating Block 5. Discoloration or Brittleness 6. Friction With Moving Parts (e.g, Nozzle Wiper) |
Bambu Lab Wiki |
| Nozzle Wiping Pad - 5 pcs |
The Nozzle Wiping Pad is used to clean the nozzle before initiating a print job. Upon each print start, the cleaning process will automatically execute without manual intervention. Replacing the silicone wiping component is part of routine maintenance. If the pad shows signs of aging, cracking, or damage, it should be replaced immediately to ensure optimal performance.
|
Bambu Lab Wiki |
| Air Filter - 1 pc | The Air Filter is installed on the inner side of the right inner liner of the printer (closer to the printer chamber) and is used to filter the air inside the chamber, effectively removing VOCs. It is advisable to replace the air filter after a total printing time of 1440 hours (or 60 days). | |
| Replacement Filament Cutter - 3 pcs | The Filament Cutter is a blade that is used to cut the filament during a filament change. The sharpness of the blade can become worse over time. We recommend replacing the filament cutter every 10-15 spools of filament used (or quicker) to ensure the cutting performance is unaffected. | |
| PTFE Tube (4000mm) - 1 pc | The function of PTFE Tube is to reduce resistance and guide filament. If the tubes are worn and not replaced in time, this may lead to feeding failures, filament accumulation inside the AMS, etc. We recommend that you check the PTFE tubes for wear during your maintenance of the machine. | |
| Lubricant Grease - 6g | Lubricant Grease is used to lubricate lead screws, or to eliminate noise issues between belts and idle pulleys. Inspect and reapply lubricant to lead screws and guide rails approximately every 3 months. | |
| Lubricant Oil (3g) - 6 pcs | Lubricant Oil is typically used for the lubrication of linear guides, slide rails, and steel shafts. Inspect and reapply lubricant to lead screws and guide rails approximately every 3 months. | |
| Nozzle Cleaning Sponge - 3 pcs | During daily printing, nozzles easily accumulate filament residue. Over time, this residue can carbonize and turn black, affecting print accuracy. This cleaning sponge is made of high-temperature resistant material and is specially designed to clean stubborn dirt from the hot-end nozzles of printers. It effectively removes carbonized residue, ensuring optimal print quality. It is compatible with nozzles on all printer models. | |
| Molecular Sieve Desiccant - 6 pcs | The molecular sieve desiccant absorbs moisture and keeps the air inside the AMS unit dry, working perfectly alongside the active heater. After the desiccant absorbs sufficient moisture, the indicating particles inside will turn from yellow to purple. When the color changes fully, it needs to be replaced with a new desiccant. | / |
| Silicone Desiccant - 6 pcs | The color-changing silicone desiccant absorbs moisture and keeps the air inside AMS unit dry. After the desiccant absorbs sufficient moisture, the yellow particles inside will turn purple. When the desiccant turns purple, it needs to be replaced with a new desiccant. | / |
For H2C
| What's in the kit? | What is it and when to replace? | How to replace? |
| Silicone Sleeve for Hotend - 3 pcs | The silicone sock is a black cover that serves the primary function of maintaining nozzle temperature stability and isolating impurities, preventing the filament from soiling the nozzle and affecting print quality. You should replace the silicone hotend cover if any of the following signs occur: 1. Cracks or Damage 2. Looseness or Detachment: 3. Deformation Due to Prolonged High Temperatures: 4. Frequent Filament Build-up on the Heating Block 5. Discoloration or Brittleness 6. Friction With Moving Parts (e.g, Nozzle Wiper) |
Bambu Lab Wiki |
| Nozzle Wiping Pad - 5 pcs |
The Nozzle Wiping Pad is used to clean the nozzle before initiating a print job. Upon each print start, the cleaning process will automatically execute without manual intervention. Replacing the silicone wiping component is part of routine maintenance. If the pad shows signs of aging, cracking, or damage, it should be replaced immediately to ensure optimal performance.
|
Bambu Lab Wiki |
| Air Filter - 1 pc | The Air Filter is installed on the inner side of the right inner liner of the printer (closer to the printer chamber) and is used to filter the air inside the chamber, effectively removing VOCs. It is advisable to replace the air filter after a total printing time of 1440 hours (or 60 days). | |
| Replacement Filament Cutter - 3 pcs | The Filament Cutter is a blade that is used to cut the filament during a filament change. The sharpness of the blade can become worse over time. We recommend replacing the filament cutter every 10-15 spools of filament used (or quicker) to ensure the cutting performance is unaffected. | |
| Filament Cleaning Pad of 4-in-1 PTFE Adapter II - 10 pcs | The Filament Cleaning Pad of 4-in-1 PTFE Adapter II is installed at the filament outlet of the 4-in-1 PTFE adapter. Its main function is to block debris on the filament at the cleaning pad side, allowing the debris to be discharged through the debris outlet on the tube expansion port. Please replace the cleaning pad when it shows obvious wear. | |
| PTFE Tube (4000mm) - 1 pc | The function of PTFE Tube is to reduce resistance and guide filament. If the tubes are worn and not replaced in time, this may lead to feeding failures, filament accumulation inside the AMS, etc. We recommend that you check the PTFE tubes for wear during your maintenance of the machine. | |
| Lubricant Grease - 6g | Lubricant Grease is used to lubricate lead screws, or to eliminate noise issues between belts and idle pulleys. Inspect and reapply lubricant to lead screws and guide rails approximately every 3 months. | |
| Lubricant Oil (3g) - 6 pcs | Lubricant Oil is typically used for the lubrication of linear guides, slide rails, and steel shafts. Inspect and reapply lubricant to lead screws and guide rails approximately every 3 months. | |
| Nozzle Cleaning Sponge - 3 pcs | During daily printing, nozzles easily accumulate filament residue. Over time, this residue can carbonize and turn black, affecting print accuracy. This cleaning sponge is made of high-temperature resistant material and is specially designed to clean stubborn dirt from the hot-end nozzles of printers. It effectively removes carbonized residue, ensuring optimal print quality. It is compatible with nozzles on all printer models. | |
| Molecular Sieve Desiccant - 6 pcs | The molecular sieve desiccant absorbs moisture and keeps the air inside the AMS unit dry, working perfectly alongside the active heater. After the desiccant absorbs sufficient moisture, the indicating particles inside will turn from yellow to purple. When the color changes fully, it needs to be replaced with a new desiccant. | / |
| Silicone Desiccant - 6 pcs | The color-changing silicone desiccant absorbs moisture and keeps the air inside AMS unit dry. After the desiccant absorbs sufficient moisture, the yellow particles inside will turn purple. When the desiccant turns purple, it needs to be replaced with a new desiccant. | / |
For H2S
| What's in the kit? | What is it and when to replace? | How to replace? |
| Silicone Sock for Hotend - 3 pcs | The silicone sock is a black cover that serves the primary function of maintaining nozzle temperature stability and isolating impurities, preventing the filament from soiling the nozzle and affecting print quality. You should replace the silicone hotend cover if any of the following signs occur: 1. Cracks or Damage 2. Looseness or Detachment: 3. Deformation Due to Prolonged High Temperatures: 4. Frequent Filament Build-up on the Heating Block 5. Discoloration or Brittleness 6. Friction With Moving Parts (e.g, Nozzle Wiper) |
Bambu Lab Wiki |
| Nozzle Wiping Pad - 3 pcs |
The Nozzle Wiping Pad is used to clean the nozzle before initiating a print job. Upon each print start, the cleaning process will automatically execute without manual intervention. Replacing the silicone wiping component is part of routine maintenance. If the pad shows signs of aging, cracking, or damage, it should be replaced immediately to ensure optimal performance.
|
Bambu Lab Wiki |
| Air Filter - 1 pc | The Air Filter is installed on the inner side of the right inner liner of the printer (closer to the printer chamber) and is used to filter the air inside the chamber, effectively removing VOCs. It is advisable to replace the air filter after a total printing time of 1440 hours (or 60 days). | |
| Replacement Filament Cutter - 3 pcs | The Filament Cutter is a blade that is used to cut the filament during a filament change. The sharpness of the blade can become worse over time. We recommend replacing the filament cutter every 10-15 spools of filament used (or quicker) to ensure the cutting performance is unaffected. | |
| PTFE Tube (4000mm) - 1 pc | The function of PTFE Tube is to reduce resistance and guide filament. If the tubes are worn and not replaced in time, this may lead to feeding failures, filament accumulation inside the AMS, etc. We recommend that you check the PTFE tubes for wear during your maintenance of the machine. | |
| Lubricant Grease - 6g | Lubricant Grease is used to lubricate lead screws, or to eliminate noise issues between belts and idle pulleys. Inspect and reapply lubricant to lead screws and guide rails approximately every 3 months. | |
| Lubricant Oil (3g) - 6 pcs | Lubricant Oil is typically used for the lubrication of linear guides, slide rails, and steel shafts. Inspect and reapply lubricant to lead screws and guide rails approximately every 3 months. | |
| Nozzle Cleaning Sponge - 3 pcs | During daily printing, nozzles easily accumulate filament residue. Over time, this residue can carbonize and turn black, affecting print accuracy. This cleaning sponge is made of high-temperature resistant material and is specially designed to clean stubborn dirt from the hot-end nozzles of printers. It effectively removes carbonized residue, ensuring optimal print quality. It is compatible with nozzles on all printer models. | |
| Molecular Sieve Desiccant - 6 pcs | The molecular sieve desiccant absorbs moisture and keeps the air inside the AMS unit dry, working perfectly alongside the active heater. After the desiccant absorbs sufficient moisture, the indicating particles inside will turn from yellow to purple. When the color changes fully, it needs to be replaced with a new desiccant. | / |
| Silicone Desiccant - 6 pcs | The color-changing silicone desiccant absorbs moisture and keeps the air inside AMS unit dry. After the desiccant absorbs sufficient moisture, the yellow particles inside will turn purple. When the desiccant turns purple, it needs to be replaced with a new desiccant. | / |
For A1
| What's in the kit? | What is it and when to replace? | How to replace? |
| Silicone Sock for Hotend - 3 pcs | The silicone sock is a black cover that serves the primary function of maintaining nozzle temperature stability and isolating impurities, preventing the filament from soiling the nozzle and affecting print quality. You should replace the silicone hotend cover if any of the following signs occur: 1. Cracks or Damage 2. Looseness or Detachment: 3. Deformation Due to Prolonged High Temperatures: 4. Frequent Filament Build-up on the Heating Block 5. Discoloration or Brittleness 6. Friction With Moving Parts (e.g, Nozzle Wiper) |
Bambu Lab Wiki |
| Heatbed Nozzle Wiper - 3 pcs |
Over time, the silicone wiper bristles can become damaged, and the metallic wiper may wear out or become bent. Common issues that may indicate the need for replacement:
1. Inadequate cleaning of the nozzle during the pre-print preparation step. 2. Filament adhering to the nozzle tip during bed leveling, resulting in an inconsistent first layer. 3. Visible damage or wear on the nozzle wiper. |
Bambu Lab Wiki |
| Purge Wiper - 1 pc | Over time, the purge wiper can become damaged, and the metallic flap of the wiper may wear out or become bent. Common issues that may indicate the need for replacement: 1. Inadequate cleaning of the nozzle during the pre-print preparation step. 2. Filament adhering to the purge wiper flap. 3. Visible damage or wear on the purge wiper. |
|
| Replacement Filament Cutter - 3 pcs | The Filament Cutter is a blade that is used to cut the filament during a filament change. The sharpness of the blade can become worse over time. We recommend replacing the filament cutter every 10-15 spools of filament used (or quicker) to ensure the cutting performance is unaffected. | |
| PTFE Tube (4000mm) - 1 pc | The function of PTFE Tube is to reduce resistance and guide filament. If the tubes are worn and not replaced in time, this may lead to feeding failures, filament accumulation inside the AMS, etc. We recommend that you check the PTFE tubes for wear during your maintenance of the machine. | |
| Lubricant Grease - 6g | Lubricant Grease is used to lubricate lead screws, or to eliminate noise issues between belts and idle pulleys. Inspect and reapply lubricant to lead screws and guide rails approximately every 3 months. | |
| Lubricant Oil (3g) - 6 pcs | Lubricant Oil is typically used for the lubrication of linear guides, slide rails, and steel shafts. Inspect and reapply lubricant to lead screws and guide rails approximately every 3 months. | |
| Nozzle Cleaning Sponge - 3 pcs | During daily printing, nozzles easily accumulate filament residue. Over time, this residue can carbonize and turn black, affecting print accuracy. This cleaning sponge is made of high-temperature resistant material and is specially designed to clean stubborn dirt from the hot-end nozzles of printers. It effectively removes carbonized residue, ensuring optimal print quality. It is compatible with nozzles on all printer models. |
For A1 mini
| What's in the kit? | What is it and when to replace? | How to replace? |
| Silicone Sock for Hotend - 3 pcs | The silicone sock is a black cover that serves the primary function of maintaining nozzle temperature stability and isolating impurities, preventing the filament from soiling the nozzle and affecting print quality. You should replace the silicone hotend cover if any of the following signs occur: 1. Cracks or Damage 2. Looseness or Detachment: 3. Deformation Due to Prolonged High Temperatures: 4. Frequent Filament Build-up on the Heating Block 5. Discoloration or Brittleness 6. Friction With Moving Parts (e.g, Nozzle Wiper) |
Bambu Lab Wiki |
| Heatbed Nozzle Wiper - 3 pcs |
Over time, the silicone wiper bristles can become damaged, and the metallic wiper may wear out or become bent. Common issues that may indicate the need for replacement:
1. Inadequate cleaning of the nozzle during the pre-print preparation step. 2. Filament adhering to the nozzle tip during bed leveling, resulting in an inconsistent first layer. 3. Visible damage or wear on the nozzle wiper. |
Bambu Lab Wiki |
| Purge Wiper - 1 pc | Over time, the purge wiper can become damaged, and the metallic flap of the wiper may wear out or become bent. Common issues that may indicate the need for replacement: 1. Inadequate cleaning of the nozzle during the pre-print preparation step. 2. Filament adhering to the purge wiper flap. 3. Visible damage or wear on the purge wiper. |
|
| Replacement Filament Cutter - 3 pcs | The Filament Cutter is a blade that is used to cut the filament during a filament change. The sharpness of the blade can become worse over time. We recommend replacing the filament cutter every 10-15 spools of filament used (or quicker) to ensure the cutting performance is unaffected. | |
| PTFE Tube (4000mm) - 1 pc | The function of PTFE Tube is to reduce resistance and guide filament. If the tubes are worn and not replaced in time, this may lead to feeding failures, filament accumulation inside the AMS, etc. We recommend that you check the PTFE tubes for wear during your maintenance of the machine. | |
| Lubricant Grease - 6g | Lubricant Grease is used to lubricate lead screws, or to eliminate noise issues between belts and idle pulleys. Inspect and reapply lubricant to lead screws and guide rails approximately every 3 months. | |
| Lubricant Oil (3g) - 6 pcs | Lubricant Oil is typically used for the lubrication of linear guides, slide rails, and steel shafts. Inspect and reapply lubricant to lead screws and guide rails approximately every 3 months. | |
| Nozzle Cleaning Sponge - 3 pcs | During daily printing, nozzles easily accumulate filament residue. Over time, this residue can carbonize and turn black, affecting print accuracy. This cleaning sponge is made of high-temperature resistant material and is specially designed to clean stubborn dirt from the hot-end nozzles of printers. It effectively removes carbonized residue, ensuring optimal print quality. It is compatible with nozzles on all printer models. |
For X1/P1 Series
| What's in the kit? | What is it and when to replace? | How to replace? |
| Silicone Sock for Hotend - 3 pcs | The silicone sock is a black cover that serves the primary function of maintaining nozzle temperature stability and isolating impurities, preventing the filament from soiling the nozzle and affecting print quality. You should replace the silicone hotend cover if any of the following signs occur: 1. Cracks or Damage 2. Looseness or Detachment: 3. Deformation Due to Prolonged High Temperatures: 4. Frequent Filament Build-up on the Heating Block 5. Discoloration or Brittleness 6. Friction With Moving Parts (e.g, Nozzle Wiper) |
Bambu Lab Wiki |
| Nozzle Wiper - 3 pcs |
The Nozzle Wiper is a flexible tool mounted on the edge of the waste chute to clean the nozzles before printing. Replace the Nozzle Wiper when it is deformed or cracked.
|
Bambu Lab Wiki |
| Activated Carbon Air Filter - 1 pc | The Activated Carbon Air Filter is used for filtering the air from the enclosure before it is expelled outside. Each one's working life is about 1440 hours (60 days) cumulative printing time. | |
| PTFE Tube Connector - 3 pcs | The PTFE Tube Connector is mounted on the back of the printer and used to connect the PTFE tube between the buffer and the toolhead. You may need to replace it when you encounter the following situations: 1. The PTFE tube can not be secured. 2. The filament cannot pass through the connector. |
|
| Replacement Filament Cutter - 3 pcs | The Filament Cutter is a blade that is used to cut the filament during a filament change. The sharpness of the blade can become worse over time. We recommend replacing the filament cutter every 10-15 spools of filament used (or quicker) to ensure the cutting performance is unaffected. | |
| PTFE Tube (4000mm) - 1 pc | The function of PTFE Tube is to reduce resistance and guide filament. If the tubes are worn and not replaced in time, this may lead to feeding failures, filament accumulation inside the AMS, etc. We recommend that you check the PTFE tubes for wear during your maintenance of the machine. | |
| Lubricant Grease - 6g | Lubricant Grease is used to lubricate lead screws, or to eliminate noise issues between belts and idle pulleys. Inspect and reapply lubricant to lead screws and guide rails approximately every 3 months. | |
| Lubricant Oil (3g) - 6 pcs | Lubricant Oil is typically used for the lubrication of linear guides, slide rails, and steel shafts. Inspect and reapply lubricant to lead screws and guide rails approximately every 3 months. | |
| Nozzle Cleaning Sponge - 3 pcs | During daily printing, nozzles easily accumulate filament residue. Over time, this residue can carbonize and turn black, affecting print accuracy. This cleaning sponge is made of high-temperature resistant material and is specially designed to clean stubborn dirt from the hot-end nozzles of printers. It effectively removes carbonized residue, ensuring optimal print quality. It is compatible with nozzles on all printer models. | |
| Molecular Sieve Desiccant - 6 pcs | The molecular sieve desiccant absorbs moisture and keeps the air inside the AMS unit dry, working perfectly alongside the active heater. After the desiccant absorbs sufficient moisture, the indicating particles inside will turn from yellow to purple. When the color changes fully, it needs to be replaced with a new desiccant. | / |
| Silicone Desiccant - 6 pcs | The color-changing silicone desiccant absorbs moisture and keeps the air inside AMS unit dry. After the desiccant absorbs sufficient moisture, the yellow particles inside will turn purple. When the desiccant turns purple, it needs to be replaced with a new desiccant. | / |
Printer Maintenance Kit
$30.93
A2L - $30.93
